Need Help? Call us at 800-386-7470 Mon - Fri., 9am-5pm CST


Welcome to Insta-Trim Boat Leveler!


Insta-Trim boat leveler's electronic tab locator shows the
position of your tabs. Two separate lines of diode lamps
accurately indicate the position of each tab. the screen is
small, mounts on the dashboard, and is designed to
match your rocker type controls in size and appearance.
The detectors are rugged and attach easily and quickly to
each hydraulic cylinder. The attached readout line runs
up to the light panel with simple plug in connections.

Insta-Trim electonic tab locators can be added to your
existing boat leveler system, upgrading your system for a
better, more accurate performance.

Installation is quick, easy, and simple. Only a few
common tools are rquired, and the tab locators come
with easy to follow instructions.


 

PART #

TAB LOCATORS
LIST

TAB LOCATOR SET ROUND BLACK INDICATOR PANEL, 25' HARNESS
350.00

TAB LOCATOR SET ROUND WHITE INDICATOR PANEL, 25' HARNESS
350.00

TAB LOCATOR SET ROUND BLACK INDICATOR PANEL, 50' HARNESS
370.00

TAB LOCATOR SET ROUND WHITE INDICATOR PANEL, 50' HARNESS
370.00

ROUND BLACK INDICATOR PANEL W/ 15' HARNESS (FLY BRIDGE)
195.00

ROUND WHITE INDICATOR PANEL W/ 15' HARNESS (FLY BRIDGE)
195.00
Legend to Tab Locator part number suffix:  BWL = Black w/ White Lettering;  WBL = White w/ Black Lettering; 
PART #

TAB LOCATOR PARTS
LIST

ROUND BLACK INDICATOR PANEL 
180.00

ROUND WHITE INDICATOR PANEL
180.00

Y-CONNECTOR, BLACK JUNCTION BOX
45.00

OUTSIDE SENSOR AND 6' CABLE
120.00

WIRE HARNESS, 25' WITH PLUG. FITS Y-CONNECTOR TO PANEL
65.00

WIRE HARNESS, 50' WITH PLUG. FITS Y-CONNECTOR TO PANEL
95.00

INSIDE SENSOR FOR PISTON CAP
25.00

BRASS SCREW FOR INSIDE SENSOR
1.00

BRACKET FOR LIGHT PANEL
15.00

NUT FOR LIGHT PANEL
5.00

 

Installation Instruction for Tablocator kit.

Inside sensor
Bring tabs to full up position, unscrew hosetrim from transom of the boat. Drill 13mm hole for hydralic hose and sensor cable. Loosen bottom large nut at base of cylinder. Then unscrew bolts fixing cylinder bracket to tab. Now unscrew large nut at base of cylinder and pull out ram.

Attach small (red) inside sensor to top of ram with the mark “A as in figure 2,2” in line with the seam. Use 3mm drill bit and drill a hole not less then 13mm deep into ram, through the hole in the inside sensor. Fasten the inside sensor with the brass screw.

With a file, make a mark on lower part of ram “B in the figure 2,2” on the same side as the mark A. Reinstall the ram in reverse process and note that mark “B” must be facing up. Do not fix hose-trim yet. Repeat procedure for next side of boat.

Outside sensor
Snap outside sensor onto cylinder with it`s cable resting against top of cylinder. Make sure outside sensors centerline is in line with hose and mark “B” on ram. Run the cable through the same hole as the hose, drill a little bit if necessary “13mm as in figure 6”. Now reinstall the hose trim.Important, leave ample loop of cable for cylinders full move see figure 10.

Instrument
Locate convenient position for instrument and saw out a hole 64mm Ø in diameter (2 ½”).Attach instrument and tighten with it´s brace. Caution: Do not over tigthen. Connect red wire from instrument to 12 or 24 volt preferably via ignition switch. Attach black wire from instrument to negative. Connect wire from sensor into the instrument. Run tabs down and the tablocator scale will gradually lighten and finally the entire scale will be illuminated.

Y connector
Attach wires from each outsidesensor to Y-connector as color marking indicates also shown in figure “9,1”. Fit Y-connector to boathull or transom with 2 small screw enclosed.

Flybridge (optional)
 Install flybridge-instrument in the same way as the standard instrument. Connect standard instrument with 0,5m / 2 Ft wire to “3-way connector for flybridge”. Run long cable from “3-way connector for flybridge” to flybridge-instrument. Connect wire from sensors into “3-way connector for flybridge”.